The partition offset feature of libisofs can produce ISO 9660 images which bear a quite conventional partition table if copied onto a USB stick. The first partition marks the size of the ISO image but starts at a non-zero address. Thus it marks a small part of the device as unclaimed by partitions and available for storing boot loader code. Nevertheless the USB stick is mountable via its overall device file as well as via the partition device file. E.g. on GNU/Linux: /dev/sdb and /dev/sdb1. This is achieved by two distinct sets of meta-data which refer to the same file content. The dual-mount feature supports Rock Ridge and eventually Joliet too. It is capable of multi-session. Currently only offset 32 kB seems to make sense. Smaller offsets are prohibited by fundamental assumptions of libisofs and libisoburn. Larger offsets would extend the unclaimed area into vital blocks of the ISO image. -------------------------------------------------------------------------- Example: Testing mountability and ISOLINUX bootability from USB stick and CD. Overview: The test image was derived from one year old RIPLinux-9.3-non-X.iso which has an isohybrid MBR. Syslinux version seems to be 3.82. That MBR and the file tree from the mounted RIPLinux image was used to build a new ISO image with 16 * 2kB partition offset. Isohybrid MBR patching was done by xorriso. Details: The first 32 kB of an ISO 9660 image are called System Area and may host any byte pattern. In the case of RIPLinux-9.3-non-X.iso only the first 512 bytes are non-zero. But to avoid any assumptions, all 32 kB get copied here. {{{ dd if=RIPLinux-9.3-non-X.iso bs=1K count=32 of=RIPLinux-9.3-non-X.sysarea }}} The files of the image are made accessible for reading {{{ mount -o loop RIPLinux-9.3-non-X.iso /mnt }}} A new ISO image gets composed. The first three lines of arguments are taken from the prescriptions of ISOLINUX wiki and adapted to the names used in RIPLinux-9.3-non-X.iso. Option -isohybrid-mbr imports the copied System Area and patches the MBR according to rules published by hpa on Syslinux mailing list. Option -partition_offset 16 causes the first partition to start at 2 kB block number 16. It also prepares the image to be mountable by this partition, too. {{{ xorriso -as mkisofs \ -o new_image.iso \ -b boot/isolinux/isolinux.bin -c boot/boot.cat \ -no-emul-boot -boot-load-size 4 -boot-info-table \ -isohybrid-mbr RIPLinux-9.3-non-X.sysarea \ -partition_offset 16 \ /mnt }}} The image was copied onto a USB stick {{{ dd if=new_image.iso of=/dev/sdc }}} and plugged into a Debian system. {{{ fdisk -lu /dev/sdb }}} yields {{{ Device Boot Start End Blocks Id System /dev/sdb1 * 64 119215 59576 17 Hidden HPFS/NTFS }}} I can mount /dev/sdb and /dev/sdb1 alike: {{{ mount /dev/sdb1 /mnt1 mount -o loop /dev/sdb /mnt }}} -o loop avoids failure with "mount: /dev/sdb already mounted or /mnt busy". A comparison by {{{ diff -r /mnt /mnt1 }}} reports no difference. Human readable files look ok. Test-reading all content by {{{ tar cf - /mnt | wc }}} yields a reasonable byte count of 60743680 and no errors. The machine boots RIPLinux from this USB stick with no visible problems. It can then mount /dev/sdb as well as /dev/sdb1. The ISO image boots from CD too. Mounting the partition can be simulated with an image file on hard disk by cutting off the first partition_offset blocks of 2 KB: {{{ dd if=new_image.iso of=partition_image.iso bs=2048 skip=16 mount -o loop partition_image.iso /mnt1 }}} -------------------------------------------------------------------------- Another test was made with GRUB 2 by downloading {{{ bzr branch http://bzr.savannah.gnu.org/r/grub/trunk/grub }}} Before building GRUB 2, the file {{{ util/grub-mkrescue.in }}} was edited to replace in the options of the xorriso command: {{{ --protective-msdos-label }}} by {{{ -partition_offset 16 -no-pad --no-emul-toc }}} Then GRUB 2 was built and installed. The resulting image from {{{ ./grub-mkrescue -o image.iso }}} was put onto USB stick. It passed the same tests on Debian as above RIPLinux example. It boots to a GRUB prompt. Due to options -no-pad --no-emul-toc the image is about 300 kB smaller than the image produced by original grub-mkrescue. Else it would have grown by about 130 kB. -------------------------------------------------------------------------- Open questions: - Shall the partition of an isohybrid image be marked bootable ? Currently xorriso keeps the 0x80 mark of an eventually imported MBR resp. the 0x80 mark which xorriso eventually sets by its own MBR preparations. - If not to be marked bootable: What equipment would the partition need to justify having the mark ? - I am still puzzled by the cylinder-head-sector ambiguity. How does a reader of the partition table determine the numbers for heads/cylinder and sectors/head ? fdisk tells about my /dev/sdb {{{ 105 heads, 17 sectors/track, 2193 cylinders, total 3915776 sectors }}} My partiton table rather was computed with 255 heads/cylinder, 63 sectors/head Debian does not mind the difference. (It uses the 32 bit LBAs, i assume.) ------------------------------------------------------------------------ Application: The partition offset feature can be controlled by libisofs API call {{{ int iso_write_opts_set_part_offset(IsoWriteOpts *opts, uint32_t block_offset_2k, int secs_512_per_head, int heads_per_cyl); }}} resp. by libisoburn calls {{{ int isoburn_igopt_set_part_offset(struct isoburn_imgen_opts *opts, uint32_t block_offset_2k, int secs_512_per_head, int heads_per_cyl); int isoburn_igopt_get_part_offset(struct isoburn_imgen_opts *opts, uint32_t *block_offset_2k, int *secs_512_per_head, int *heads_per_cyl); }}} resp. by xorriso options {{{ -boot_image any partition_offset=(2kb_block_adr) -boot_image any partition_sec_hd=(number) -boot_image any partition_hd_cyl=(number) -as mkisofs ... -partition_offset (2kb_block_adr) ... }}} As stated above, an offset larger than 16 would expose vital parts of the ISO image as unclaimed space. Values smaller than 16 are not accepted. So use either an offset of 16 blocks or keep the feature disabled by offset 0.